Home > Device Driver > Device Driver 8505xl

Device Driver 8505xl

You must ensure that the drive sled assembly is set to single-ended operation. Page 37: Troubleshooting, Problems With Tape Drive Installation • If you have IRIX 5.3, make sure that the additional driver software is installed on the system. Don't show me this message again. Shoreline Blvd., Mountain View, CA 94043-1389. useful reference

All rights reserved. ‏لاستخدام مجموعات Google، يرجى تمكين جافا سكريبت في إعدادات المتصفح، ثم تحديث هذه الصفحة. . حسابيبحثخرائطYouTubeالأخبارGmailDriveتقويمGoogle+‎ترجمةالصورالمزيدالمستنداتBloggerجهات الاتصالHangoutsKeepتلقّي المزيد من Googleتسجيل الدخولالحقول المخفيةبحث عن مجموعات أو رسائل Copyright © 2017 Retrospect, Inc. Page 8 viii... Page 22: Turning On Power To The Tape Drive, Installing Your Driver Software, Testing Your Installation The 8505XL requires IRIX 5.3, 6.1, or later software for proper operation. my review here

The 8505XL uses this stripe to distinguish data-quality metal-particle media, such as EXATAPE, from other 160-m media. Page 39 If you are experiencing operating problems loading or unloading a data cartridge, check the following: • Make sure that your system is turned on. Table 2-2...

When the green LED is on solid, the tape drive is ready. Page 14 ID, you must change the tape drive’s ID. Page 34: Using The Cleaning Cartridge If there is no cleaning material remaining, discard the cleaning cartridge and use a new one. Reusing a cleaning cartridge redistributes contaminants previously removed from the tape path.

Page 4: Table Of Contents Contents Operating the Tape Drive 17 Reading the LEDs 17 Selecting Data Cartridges 19 Write-Protecting a Data Cartridge 20 Loading a Data Cartridge 20 Unloading a User input. Caution: Use proper handling and storage procedures to minimize the loss of data and equipment. Description - About Us Press Support Privacy Downloads Upgrade Buy Try Facebook Twitter LinkedIn YouTube Spiceworks Kiva Blog Choose your language: Deutsch English English-AU English-UK Español Français Italiano Latin America

Contractor/manufacturer is Silicon Graphics, Inc., 2011 N. Wait while the tape drive loads the tape, determines the tape format, and positions the tape to the logical beginning of the tape (LBOT). Page 19: Installing Into A Horizontal Drive Bay, Installing Into A Vertical Drive Bay Follow these instructions to install a half-height front-loading device: Installing Into a Horizontal Drive Bay Follow these The 8505XL uses 8-mm format tapes and installs in most of the existing Silicon Graphics© systems and data storage units that support single-ended, front-loading drives (FLDs).

Press the unload button to clear the error, then try loading the data cartridge again. http://playgroundboston.com/2015/12/30/fedora-driver-for-8505xl/ Page 17 (see Figure 1-1). Page 25 4. Sign up!

Using this cleaning cartridge regularly allows you to maintain data integrity and improve reliability of the tape drive. http://connectwithcanopy.com/device-driver/device-driver-communications-port-com1-device-preventing.php Page 32 Chapter 2: Operating the Tape Drive... Page 18: Terminating The Scsi Bus, Installing The Tape Drive Chapter 1: Installation Single−ended, 50−pin SCSI drive on channel A Setting the Drive Sled for Single-Ended Operation Figure 1-3 Your system Page 33: Preventive Maintenance, Recommended Cleaning Cartridges, Determining When To Clean The Tape Drive Silicon Graphics recommends that you clean your tape drive with the Exabyte 8 mm cleaning cartridge (supplied

Unpack the tape drive and save the packing materials (see “Unpacking the Tape Drive and Saving the Materials”... Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 If a Note: hardware error occurs, press the unload button to reset the tape drive. http://connectwithcanopy.com/device-driver/developing-embedded-linux-device-drivers-for-a-system-on-chip-device.php Restore password × Upload manual upload from disk upload from url Thank you for your help!

Page 2 States. Orient the FLD and sled assembly so that the connectors on the back are on the bottom half of the drive and face away from you (see Figure 1-4). Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Exabyte Manuals Storage 8505XL Owner's manual Exabyte 8505XL Owner's Manual 8-mm tape drive.

Perform a backup operation to write a small amount of data to the tape (see your IRIX administration documentation, as required). 5.

You can use the unload button to clear some hardware errors. If your Note: system already has IRIX 6.1, software driver installation is not required. • testing your installation To install the tape drive properly, follow all of the instructions in this Page 23 1. Remove the drive adapter and power cables from the 8505XL (see Figure 1-1) and then place the drive on an anti-static surface. 3.

Page 5 Installing the Tape Drive Into a Horizontal Drive Bay 10 Figure 1-4 Installing the Tape Drive Into a Vertical Drive Bay 11 Figure 1-5 Write-Enable/Disable Switch 13 Figure 1-6 On the label, you may want to include the cartridge number (log number), date of backup, and format of the tape. If your system has IRIX 6.1 or later software, no additional driver software is required. Get More Info The 8505XL ships with a cleaning cartridge that can be used for up to nine cleanings.

Be sure each SCSI Note: device on a bus has a unique SCSI address (ID). Page 12: Preparing For Installation, Ensuring Esd Protection Chapter 1: Installation Preparing for Installation To prepare for installation, follow the steps described in this chapter. 1. The video-grade tape is also more abrasive to tape-drive recording heads. Table A-1 Drive Specifications Parameter Interface Capacity 8200 format 8200c format Note: This assumes a 2:1 compression ratio 8500 format 8500c format Physical Characteristics Size...

Extra jumpers are shipped in a separate bag. After checking all the items listed, reset the SCSI bus by resetting the system. IRIX and Silicon Graphics are registered trademarks and CHALLENGE and Onyx are trademarks of Silicon Graphics Corporation. Follow these steps to change the SCSI ID of the 8505XL: The 8505XL SCSI jumpers are located in the back of the drive and are Note: covered by the drive sled